Band Saws continued

I made an extensive power point for explaining the workings of a band saw including use and safety. Showed this to students in class. Then I made a multiple choice and short written response quiz on Moodle so they could test on-line. Haven’t scored the tests yet.

Meanwhile I am one by one having them practice and demonstrate the use of the band-saw with me at their side. I have gotten through 6 of 24 students. I have them practice on a mock band saw first so they learn not to twist the blade. Most students get it. A few have not and at least one of them twisted the mock band saw hard enough to bend the blade. I have thought of making a mock band maze where they have to get a pre-cut path pushed along a blade with out touching the edges. That can be an electrical circuit with a buzzer. The edges of the cut will be lined with copper tape so that if the blade touches, it will set off the buzzer. A successful trial will be getting through the whole path without setting off the buzzer.

I have a sub today. I left instructions for the students to begin their marble mazes. They will eventually be stacked one above the other so students need to identify the entry and exit points on their maze boards. They then draw their maze out and trace it on tracing paper. They will be gluing their tracing paper cut-outs onto some MDF to cut the maze paths on the bandsaws. This will afford them a low-consequence opportunity to hone their band-saw skills.

Marble Maze

The electronics unit ended with a whimper. A few students still need to finish the required circuit. I did not have time to make an electronics quiz. I did have them put up their hacked notebooks with an LED and a hand-made switch.

Students will soon take the drill press quiz on-line. They will need to use drills for the Marble Maze activity.

I have had them start making spoons by using gouges and mallets on short blocks of Alder. They are taking to it readily. The next step of the spoons will be for them to make cuts on the bandsaw. The main activity that requires the use of the band saw is to make a marble maze. I still need to make a sample marble maze for them to emulate.

I am wondering how to set things up so I can get all the students passed to run the band saws. There are several steps and it should take 1 – 2 weeks.

  • Demonstration by me. (I would like to have my demonstration recorded on video. Easy to make rough but if it needs any editing that is time I might not have.)
  • We review vocabulary and safety rules as a class.
  • Students practice on a mock-up band-saw to get a feel for how to make the curves.
  • Each student demonstrates that they can do basic adjustments on the Band saw and cut curves on practice stock.
    • There are only three band saws to use and I have 24 students. Having another activity for the other students can be challenging. The ones who learn the band-saw quickly can work on their spoons. For some of them, I could cut out the spoons on the band saw for them and then they will have a lot of work filing and sanding their spoons.
  • Students take a paper quiz. They must get 100%.
  • Once they have demonstrated safe use and passed the quiz, then they have permission to use the band saws.

What will happen Thursday?

I want to make a quiz course where students will have to take a multi-meter and measure an assortment of resistances, currents and voltages. I also want them to be able to do calculations.This is going to be a formative assessment since I think only a fraction of the student know how. It will give them an idea of what they still need to learn. Then I can give a summative test.

Preparation and planning for the coming week.

Picture of a rolling cabinet.

The Electronics Cart

So I spent many hours organizing electronics components into bins designed for student access. I have them on a cart so that I can roll it away. Also on the cart are three locking drawers. In those drawers are the precious things that I want to personally hand to students as they need them.


The parts trays off the cart and spread out ready for use.

I also set up a soldering area and hooked up a fume extractor that was too small for use with our laser cutter.


Here isĀ  a neat tidbit: I had made a 5 volt power supply box with alligator clip leads. To prevent students from shorting the supply, I had thin wires across contacts. Of course it was too much fun to short the supply and watch the wires melt. So I found a automatically resetting fuse to complete the circuit.

The main activity for tomorrow will be for them to hack their notebooks. I have some small sticky LEDs, a bunch of copper tape, and some 2032 batteries. I will allow them to wire up and keep the setup for any notebook they own. The sticky LEDs are very expensive. Some of my students who already know how to solder, can use a quantity of multi-color LEDs that are very cheap but that need leads connected to them.

Here is my notebook hack. Pushing down in a few places makes the lights go on. IMG_0246

Project Ignite from Autodesk

I have had students working with I set up a classroom on there. Students have been working their way through the set: Let’s Learn Circuits.

As they have done so, I made some checkpoints.Here they are. Students needed coaching to get their schematics simplified without a bunch of crossing lines. Some students switched the bulb off by shorting the battery. This did not make an exploding battery in 123D circuits as I wished.

For the second checkpoint, students had to learn to put the Multimeter in series and set it to Current.

The 3rd checkpoint has a worksheet to go with it. It takes a bit of Algebra. Some student have not taken Algebra yet. Here is the worksheet: LetsLearnCircuitsResistors

Some students who could not do the computer part, were able to make the circuit on a breadboard.

Great success with the breadboards.

Now I have to enter into my gradebook, who made it through the checkpoints.

  1. In Lesson 2
    1. Show me on your screen that you have made a circuit with a switch that turns a light on and off.
    2. Clean up the Schematic as needed in the schematic view.
    3. Sketch the schematic in your notebook. Show me.
  2. In Lesson 4
    1. Show me your circuit with the LED, the resistor, and the multi-meter measuring the current.
    2. Sketch the schematic in your notebook. (Clean up the sketch in the schematic view if it helps.)
    3. Make the circuit with actual bulbs, resistor, battery, and multi-meter on a breadboard. (Hint: The multi-meter must be connected in series. The bulb should only light when the multi-meter is connected. You are measuring current so the entire current has to go through the multi-meter.)
  3. In Lesson 5 (There is a worksheet to go with this one. The instructions are also on the worksheet.
    1. Set up the resistors and the multi-meter as shown in Lesson 5. One pair of resistors is in parallel, the other pair is in series.
    2. Sketch the circuit on the worksheet and then do the Algebra to find the combined resistances. If you like, you can check your answer by setting the resistors to the values shown on the worksheet and take the readings from the multimeters in 123D circuits.
    3. Turn in this worksheet.
  4. In Lesson 5 part 8
    1. Determine the answers to parts 1, 2, and 3. Part 4 is challenging. Try it.
    2. For at least 1, 2, and 3. Show your Algebra work in your notebook. Use a separate page. Show Mr. Monley.

Planning the Maker course

This course’s official name is Computer Applications/Principles of Technology. These names describe courses already listed for our school district. They match what will be the content for a Maker course. I will be recording my experience as teacher of this course through this blog.

After talking pedagogy with Howard Rheingold this morning, I have begun to see this course as a process for both myself and the students. Some essential questions for me are: in my mind is

  • How can I hand the responsibility for learning over to my students?
  • How can I ensure that the students are interested in exploring, experimenting and learning?

Here is a link to the Student Page